Bring your Schluter®-DITRA-HEAT-E-WiFi floor warming thermostat into
Control4 as a true, native thermostat. This driver connects through the
same Schluter cloud account used by the Schluter app — no extra
hardware, hubs, or local wiring — and keeps Control4 in sync with the
floor's live temperature, target setpoint, heating activity, and
operating mode.
The thermostat appears on Control4 touchscreens, remotes, keypads, and
the Control4 app exactly like any other thermostat in the system: see
the current floor temperature at a glance, adjust the setpoint, and
automate it from Composer programming alongside the rest of the home.
**Features**
- Native Control4 thermostat (thermostatV2 proxy) — live floor
temperature, setpoint, and heating/idle state on every Control4
interface
- Full mode control — Heat (the app's "Manual"), Automatic (follows the schedule set in
the Schluter app), Off, and Frost Safe — from the thermostat's Mode
button, the Extras page, Composer properties, one-click quick
actions, and a "Set Schluter Mode" programming command
- Two-way sync: setpoint and mode changes made in the Schluter app are
reflected back into Control4 automatically (configurable polling,
5–300 seconds)
- Multi-thermostat accounts supported — pick the right unit from a
dropdown listing each thermostat as "device - room"; the Control4
device auto-names itself to the thermostat's room on first connect
- GFCI fault status surfaced in the connection status, so a tripped
floor-heating circuit doesn't go unnoticed
- Fahrenheit or Celsius display per Control4 preference, independent of
the thermostat's own display setting
- Clear, plain-language connection status — including when the Schluter
account has hit its concurrent-session limit
**Requirements & notes**
- Schluter DITRA-HEAT-E-WiFi thermostat (DHERT10x family) already set
up in a Schluter account via the Schluter app
- Control4 OS 3.x and a controller with internet access
- One driver instance per physical thermostat
- Non-WiFi DITRA-HEAT-E models (RT/RS/RSD without WiFi) are not
supported — they have no cloud account
- Schluter accounts allow a limited number of simultaneous logins
(three observed); this driver uses one. If the account is already at
its limit, sign out of an unused device and the driver connects on
its next attempt.
- Schluter currently operates two separate account systems, and this
driver automatically detects and connects to either one — confirmed
working live against both, including multi-thermostat accounts on the
older system. The older system supports Heat (temperature) control
only, without Automatic/Off/Frost Safe mode switching; the "Schluter
Mode" property and Extras page Mode selector don't appear on those
accounts since there's nothing there for them to control.
Cloud-based control depends on Schluter's service being reachable;
PROSTUP LLC is not affiliated with Schluter Systems. Schluter and
DITRA-HEAT are trademarks of Schluter Systems.
Control4 as a true, native thermostat. This driver connects through the
same Schluter cloud account used by the Schluter app — no extra
hardware, hubs, or local wiring — and keeps Control4 in sync with the
floor's live temperature, target setpoint, heating activity, and
operating mode.
The thermostat appears on Control4 touchscreens, remotes, keypads, and
the Control4 app exactly like any other thermostat in the system: see
the current floor temperature at a glance, adjust the setpoint, and
automate it from Composer programming alongside the rest of the home.
**Features**
- Native Control4 thermostat (thermostatV2 proxy) — live floor
temperature, setpoint, and heating/idle state on every Control4
interface
- Full mode control — Heat (the app's "Manual"), Automatic (follows the schedule set in
the Schluter app), Off, and Frost Safe — from the thermostat's Mode
button, the Extras page, Composer properties, one-click quick
actions, and a "Set Schluter Mode" programming command
- Two-way sync: setpoint and mode changes made in the Schluter app are
reflected back into Control4 automatically (configurable polling,
5–300 seconds)
- Multi-thermostat accounts supported — pick the right unit from a
dropdown listing each thermostat as "device - room"; the Control4
device auto-names itself to the thermostat's room on first connect
- GFCI fault status surfaced in the connection status, so a tripped
floor-heating circuit doesn't go unnoticed
- Fahrenheit or Celsius display per Control4 preference, independent of
the thermostat's own display setting
- Clear, plain-language connection status — including when the Schluter
account has hit its concurrent-session limit
**Requirements & notes**
- Schluter DITRA-HEAT-E-WiFi thermostat (DHERT10x family) already set
up in a Schluter account via the Schluter app
- Control4 OS 3.x and a controller with internet access
- One driver instance per physical thermostat
- Non-WiFi DITRA-HEAT-E models (RT/RS/RSD without WiFi) are not
supported — they have no cloud account
- Schluter accounts allow a limited number of simultaneous logins
(three observed); this driver uses one. If the account is already at
its limit, sign out of an unused device and the driver connects on
its next attempt.
- Schluter currently operates two separate account systems, and this
driver automatically detects and connects to either one — confirmed
working live against both, including multi-thermostat accounts on the
older system. The older system supports Heat (temperature) control
only, without Automatic/Off/Frost Safe mode switching; the "Schluter
Mode" property and Extras page Mode selector don't appear on those
accounts since there's nothing there for them to control.
Cloud-based control depends on Schluter's service being reachable;
PROSTUP LLC is not affiliated with Schluter Systems. Schluter and
DITRA-HEAT are trademarks of Schluter Systems.
No posts found
